Cable basket fixing is quick work, and that is where the risk lies. With click-fit couplers and a box of drop rods, a fitter can hang a long run in an afternoon. Without a plan for support centres, couplers and earth continuity, part of it comes down again at snagging. Here are the six usual ways of fixing cable basket, the spacing, how to cut bends and join lengths, and the sizes and finishes you will find in UK ranges.
What are the ways to fix cable basket?
| Method | Where | Limit or feature |
|---|---|---|
| Centre hanger | Soffit, single drop rod | Basket widths 100 to 200 mm [1]; UK hangers for M10, 10.2 mm hole [2] |
| Omega support | Soffit, single drop rod | Up to 300 mm wide on one central rod [1] |
| Trapeze with strut channel | Soffit, two drop rods | Wide and heavy basket, multi-tier runs |
| C-bracket | Wall or drop rod | Side entry for cables, 100 to 400 mm [1] |
| Cantilever bracket | Wall, column | Holds basket clear of the wall on longer runs [2] |
| Stand-off support | Wall or floor | 40 mm clear of the surface, 180 and 350 mm lengths [1] |
Manufacturer data [1][2], application indicative.
Centre hangers and C-brackets share one big advantage: one side of the basket stays open, so cables can be laid in from the side instead of threaded through. On a long run that saves a lot of time.
How do you fix cable basket to the soffit?
For a trapeze, the sequence is:
- Soffit fixing. Two anchors or beam clamps per support. Choose the anchor for the substrate and load; the anchor manufacturer gives the permissible load.
- Drop rods. Screw the studding into the anchor and lock it with a nut. M8 is common for light basket and M10 for most trapezes (rule of thumb, indicative).
- Cross-member. Set the strut channel to level and fix it with channel nut, washer and nut above and below.
- Basket. Lay the basket on the cross-member and secure it with a hold-down clamp. UK ranges use a nut, bolt and clamp assembly or a large clamp with a 6.5 mm hole [2].
- Check. Line the basket up over at least three supports and re-tighten everything.
For narrow basket, a centre hanger is faster: one drop rod per support and the basket drops into the hanger. To work out the load at each support, see cable tray supports.
How do you fix cable basket to walls and floors?
On walls, use a C-bracket or a cantilever bracket. A C-bracket keeps the basket close to the wall and leaves the side open. A strut cantilever arm holds it further out and carries more. Size the arm at basket width plus 50 mm (rule of thumb, indicative).
On floors, or vertically on a wall, use stand-off supports. They hold the basket 40 mm clear of the surface, leaving room for cleaning and cable ties [1]. Their U-shape copes with uneven surfaces. In a raised floor void, low frames are common. See raised access floor cabling.
How often should cable basket be supported?
| Situation | Support centres (rule of thumb) |
|---|---|
| Basket 30 or 55 mm deep, normal fill | 1.5 m |
| Basket 106 mm deep, full | 1.2 to 1.5 m |
| Extra support at bends, tees, ends | within 0.5 m |
| Fire-rated (circuit integrity) runs | as per the test report |
Rule of thumb, indicative. The manufacturer’s load chart governs.
Manufacturers often publish basket loads as a chart of permissible kg/m against support centres. Read off the figure for your basket and add up the cable load. A full 600×100 mm basket with 480 Cat6A cables weighs about 32 kg per metre: 3.09 kg/m of basket [1] and the rest cable (rule of thumb, indicative).
How do you cut bends and join lengths?
Cable basket needs few separate fittings. You make bends, tees and reducers yourself:
- Cut. Use bolt croppers to remove wires from the base and sides where the basket needs to turn. Cut flush, leaving no sharp points.
- Bend and join. Bend the basket to angle and join the pieces with splice plates or couplers. UK ranges include splice plates and click-fit couplers [2].
- Protect. Fit wire end protectors to the cut ends so they cannot damage cables or hands [1].
Metal containment is bonded as required by BS 7671 [4]. With the right couplers, earth continuity is assured to IEC 61537 [1][3]. Where a section is interrupted, at a fire barrier or a movement joint for example, bridge it with a braided copper bonding connector of 12 or 16 mm² [1].
What mistakes come up most with cable basket?
- Hanging from the ceiling grid. Basket always hangs from the main structure. The grid of a suspended ceiling is not designed for it.
- Cut ends left sharp. Sharp wire ends damage cable sheaths during the pull.
- No support at a site-made bend. A cut bend is less stiff than a straight length. Support it within 0.5 m (rule of thumb, indicative).
- Broken earth continuity. A joint without continuity, or an interruption without a bonding connector.
- Too few hold-down clamps. Without clamps the basket slides off the cross-member when cables are pulled in.
Which sizes and finishes are common in the UK?
| Feature | Common |
|---|---|
| Depth | 30, 55 and 106 mm; continental ranges 35, 60 and 100 mm |
| Width | 50 to 600 mm |
| Length | 3 m |
| Finish | Electro-zinc, pre-galvanised, powder-coated, zinc-aluminium, hot-dip galvanised, stainless steel |
| Standard | IEC 61537 (BS EN 61537) |
Manufacturer data [1][2].
Electro-zinc suits dry indoor areas. Hot-dip galvanised is for outdoor, damp and industrial areas, and stainless steel 316 for food, chemical and coastal sites. Zinc-aluminium is offered as a further option for damp environments [2].
In the configurator you add cable basket as a tier on the trapeze. Supports, couplers and hold-down clamps go into the bill of materials, together with the cables in the basket.
Where do these figures come from?
- Eurostrut, wire basket and accessory product pages: centre hanger (M6, M8, M10; 100 to 200 mm), omega support (one rod up to 300 mm), C-bracket (100 to 400 mm), stand-off support (40 mm; 180 and 350 mm), couplers, wire end protector, bonding connector 12 and 16 mm², 100×600 mm basket at 3.09 kg/m. Accessed 19 November 2026. https://eurostrut.com/kabeldraagsystemen/pemsa-rejiband-draadgoten/
- Atkore UK, steel wire cable tray and accessory product pages: suspension hanger 10.2 mm, universal support bracket, cantilever bracket, splice plate, clamp with 6.5 mm hole, click-fit coupler; depths 30, 55 and 106 mm; finishes. Accessed 19 November 2026. https://www.atkore.com/en-gb/products/cable-management-systems/MCSH
- IEC 61537 (BS EN 61537), Cable management. Cable tray systems and cable ladder systems.
- BS 7671, Requirements for Electrical Installations (IET Wiring Regulations).
Frequently asked questions
How do you hang cable basket from the soffit?
Narrow basket up to about 200 mm wide hangs from a single drop rod on a centre hanger (manufacturer data). Wider or heavier basket goes on a trapeze: two drop rods with a strut channel cross-member and hold-down clamps.
How often should cable basket be supported?
As a rule of thumb every 1.5 m, so two supports per 3 m length, plus a support near every bend, tee and end (indicative). Go shorter for a full 106 mm deep basket. The manufacturer's load chart governs.
How do you make a bend in cable basket?
Cut wires out of the base and sides with bolt croppers, bend the basket to the angle you need and join the pieces with splice plates or couplers. Fit wire end protectors to cut ends so they cannot damage cables or hands.
What size drop rod is used for cable basket?
M6 to M10 depending on the hanger and the load. UK centre hangers are often made for M10 studding, with a 10.2 mm hole (manufacturer data). Check the load per rod against the anchor and rod capacity.
https://strutconfigurator-site.pages.dev/en/knowledge-base/cable-basket-fixing/ · Updated 19 November 2026 · Indicative; the manufacturer confirms.