Strutconfigurator
Fixings

Channel nuts and spring nuts for strut: types and fitting

Updated 5 min readBy Ismail Yeşilay · Strutconfigurator

Short answer

Channel nuts are rectangular nuts with two grooves that lock behind the serrated lips of strut channel. Use short spring nuts in 41x21 channel and long spring nuts in 41x41 and deeper sections. M6 to M12 are standard, with plain nuts also in M16. Strutconfigurator counts the channel nuts for every joint in the bill of materials.

Channel nuts turn a length of strut into a system. You drop one into the channel wherever you need it, give it a quarter turn and bolt on a fitting, rod or bracket. Installers in the UK mostly call them spring nuts, after the spring that holds them in place. There are five common types and each suits a channel depth. This guide covers which nut goes where, how to fit it and where its limits are.

A channel nut is a rectangular nut with two grooves across its top face. The grooves lock behind the inturned, serrated lips of the channel. The nut cannot pull out of the slot, and the serrations stop it sliding along the rail once the bolt is tight [1][2].

Which types of channel nut are there?

Type Thread Channel depth Use Source
Plain (no spring) M6, M8, M10, M12, M16 all depths Horizontal runs, fixed positions; M16 for heavy joints [1][2]
Short spring M6, M8, M10, M12 21 mm 41×21 channel [1][2]
Long spring M6, M8, M10, M12 41, 62 and 82 mm Standard for 41×41 and deeper, including vertical runs [1][2]
Plastic retainer M6, M8, M10, M12 41 mm Quick positioning without the nut dropping [1][2]
Stud nut M6 to M12; stud 30–100 mm 41 mm Hanging items directly, fixing brackets [1][2]

Manufacturer data. Available combinations vary by supplier.

Why does a 34.5 mm nut fit a 22 mm slot?

A channel nut for 41 mm channel is 34.5 mm long and 20 mm wide [1]. The slot opening is 22 mm [3]. That difference is the whole principle: across its width the nut passes through the slot, along its length it spans the lips. Insert it at an angle, turn it a quarter and it locks.

If you manage product data: channel nut threads are made to the tolerances of ISO 965-2, a nut weighs 31 to 48 g depending on size and spring, and Vergokan files them under ETIM class EC000096 [2].

How do you fit a channel nut?

  1. Pick the right nut. Thread to match the bolt or rod, spring to match the channel depth, finish to match the channel.
  2. Insert it at an angle, grooves facing the lips.
  3. Turn it a quarter turn. The grooves now sit behind the serrations. Feel that it has locked before you let go.
  4. Slide it into position. The spring keeps it there, even in vertical channel.
  5. Fit the bracket with a washer or square washer plate and start the bolt.
  6. Tighten to the stated torque. The figure is in the manufacturer’s installation instructions. Too loose and the joint slips; too tight and the lips deform.

After tightening, check that both grooves really sit behind the serrations. A nut riding half on a lip feels tight but slides under load.

How much load can a channel nut take?

A channel nut fails in one of two ways. Force at right angles to the channel pulls the nut out: pull-out. Force along the channel makes it slide: slip.

Load direction What happens Depends on
Perpendicular to the channel (pull-out) Lips open up and the nut comes free Gauge, lip profile, thread size
Along the channel (slip) Nut slides over the serrations Serrations, torque, washer
Combined Both at once; the lower limit governs Manufacturer data for the assembly

Overview from practice, indicative.

Our sources publish no figures for the standard 41 mm nut [4]. To see what such data looks like, one manufacturer gives 8.9 kN pull-out and 6.7 kN slip at a safety factor of 3 for its heavy-duty 80×80 mm system [5]. That is a different system, and the values do not transfer to 41 mm channel. Ask for both figures for your system and apply them only with the channel they were tested in.

Which finish should the nut have?

Match the nut to the channel’s corrosion class. An under-specified nut is where rust starts, and a corroded nut can no longer be adjusted.

  • Pre-galvanised channel, dry indoors: zinc-plated nuts are the norm.
  • Hot-dip galvanised channel: galvanised nuts with galvanised bolts and nuts.
  • Stainless channel: stainless nuts, also available in 316 for hygienic areas [6].

How many channel nuts does a trapeze hanger need?

In a standard 41x41 trapeze, each rod gets one long spring nut per tier in the rod’s thread size, usually M10. Below the cross member go a washer or square plate and a hex nut, with a lock nut under the bottom tier. Tray or ladder is held down with clamps on further channel nuts.

Trapeze Channel nuts for the rods Channel nuts for containment clamps
1 tier, 2 rods 2 2 to 4
2 tiers 4 4 to 8
3 tiers 6 6 to 12

Worked example, indicative. The clamp count depends on the containment and the manufacturer’s instructions.

The full assembly is set out in how to assemble a trapeze bracket, and rod capacity in the threaded rod load table.

What mistakes come up most often?

  • Long spring nut in 41x21 channel. It will not fit. Use a short spring or a plain nut.
  • Nut not turned. The grooves then run parallel to the lips and grip nothing.
  • Mixing brands on a calculated support. Many nuts fit another maker’s 41 mm channel, but load data covers only the tested combination. See compare strut systems.
  • Zinc-plated nuts outdoors. The thin coating rusts quickly. Match the nut to the channel, as set out in pre-galvanised vs hot-dip galvanised vs stainless.
  • No washer or plate. Without one, the load concentrates on a small area and the fitting deforms sooner.

Where do these figures come from?

  1. Eurostrut, channel nut product pages (plain M6 to M16, short and long spring, plastic retainer, 34.5 mm long, 20 mm wide, stud nuts M8 to M12 with 30 to 100 mm studs). Accessed 19-11-2026. https://eurostrut.com/strut-glijmoer-met-lange-veer-m10-hdg-iso/ES1008HDG · https://eurostrut.com/strut-glijmoer-met-korte-veer-m12-hdg-iso/ES4010HDG · https://eurostrut.com/strut-glijmoer-m16-41mm-hdg-iso/ES3016HDG
  2. Vergokan (part of Atkore), short spring nut (for 41×21), long spring nut (for 41×41), PVC retainer nut and stud nut M6 to M12 (weight, ISO 965-2, ETIM class). Accessed 19-11-2026. https://www.vergokan.com/nl/kabeldraagsystemen/Montagesystemen/Montagetoebehoren/PNS · https://www.vergokan.com/nl/kabeldraagsystemen/Montagesystemen/Montagetoebehoren/PNL · https://www.vergokan.com/nl/kabeldraagsystemen/Montagesystemen/Montagetoebehoren/PNK · https://www.vergokan.com/nl/kabeldraagsystemen/Montagesystemen/Montagetoebehoren/SN
  3. Eurostrut, 41×41 mm channel (22 mm slot opening). Accessed 19-11-2026. https://eurostrut.com/montageprofiel-41x41mm-met-gaten-3m-tv/ES1000THDG3M
  4. Strutconfigurator standard catalogue v0.1 (19-11-2026): no public load data for the standard 41 mm channel nut in the Eurostrut, Vergokan or Atkore UK sources.
  5. Atkore UK, Heavy Duty Channel Nut for the 80×80 system (pull-out strength and slip capacity). Accessed 19-11-2026. https://www.atkore.com/en-gb/products/metal-framing-and-fittings/Heavy-Duty-Channel-Nut
  6. Atkore UK, short spring channel nut in type 316 stainless for standard channel. Accessed 19-11-2026. https://www.atkore.com/en-gb/products/metal-framing-and-fittings/PNS06-PNS12A

Frequently asked questions

How do you fit a spring channel nut?

Push the nut into the slot at an angle with the grooves facing the lips. Turn it a quarter turn so the grooves lock behind the serrations. Slide it into position, add the fitting with a washer and tighten the bolt to the torque in the manufacturer's instructions.

Short spring or long spring: which do I need?

It depends on channel depth. Short spring nuts are for 21 mm deep channel such as 41x21. Long spring nuts are for 41, 62 and 82 mm deep channel. A long spring will not fit a 21 mm section; a plain nut fits all depths.

How much load can a channel nut take?

It depends on thread size, channel gauge, tightening torque and load direction. Our sources publish no figures for the standard 41 mm nut. Ask the manufacturer of the system you install, and use the values only with that manufacturer's own channel.

What is a stud nut?

A channel nut with a fixed threaded stud, available from M6 to M12 with studs of 30 to 100 mm. It hangs something directly under a rail or fixes a bracket without a loose bolt, which speeds up repetitive fixing.

Next step

See your own range in 3D.

In 30 minutes we show how your installers configure, what arrives on your side and what the client version on your range involves.

Manufacturer or wholesaler

Book a demo with Ismail

You see the configurator in your own brand and we discuss your range, systems and markets.

Reply from Ismail within one working day

Installer

Configure for free

A trapeze, frame or tray with cables in a few minutes, with a bill of materials and drawing.

Enquiry goes to a supplier · reply within one working day