Strutconfigurator
Comparing brands

Compare strut systems: Unistrut, Hilti, Sikla, Walraven

Updated 5 min readBy Ismail Yeşilay · Strutconfigurator

Short answer

Unistrut, Hilti, Sikla, Walraven, MÜPRO, fischer and OBO Bettermann all supply complete support systems: strut channel, channel nuts, fittings and fixings. They differ in design software, engineering services, how they publish load data and how they reach site. The 41 mm format is widespread, yet load data is brand-specific. Strutconfigurator is independent of all of them.

To compare strut systems fairly, you need to look past the channel itself. Unistrut, Hilti, Sikla, Walraven, MÜPRO, fischer, OBO Bettermann and Gripple all sell into UK and Irish M&E projects, and their 41 mm channel looks much the same on a pallet. The differences sit in design software, load data, heavy-duty ranges, documentation and how the product reaches site. This overview sets them side by side without favouring any of them.

A support system is a matched range for fixing building services to a structure: strut channel, channel nuts, fittings, threaded rod, anchors, beam clamps, and clips for pipes and cables. Strutconfigurator is not a dealer or partner of any brand mentioned. Everything below comes from public sources [1–10].

Which strut and support brands will you meet on UK projects?

Brand Based in Known for Online tools (found 19-11-2026)
Unistrut (Atkore) United States Strut channel dating back to 1924, BS 6946 channel in the UK [8] Hanger Configurator and BIM Toolbar, US range [7]
Hilti Liechtenstein MQ and MT installation systems, anchors PROFIS Installation [4]
Sikla Germany Support systems for building services SiCAD plug-ins for Revit, E3D and S3D, planning service [3]
Walraven Netherlands Fixing systems, BIS RapidRail and RapidStrut channel Online datasheets and web catalogue [1]
MÜPRO Germany Fixing systems for services Browser calculators, MP Designer 3D, apps [2]
fischer Germany Anchors and installation fixings FiXperience INSTALL-FIX, cloud-based since November 2025 [5]
OBO Bettermann Germany Cable support systems and channel OBO Construct: cable fill and AutoCAD add-in [6]
Gripple United Kingdom Wire rope suspension Not researched

Public information from our research on 19-11-2026. Ranges and tools change; check with the manufacturer for the current position.

How do Unistrut, Hilti, Sikla and Walraven differ?

All four cover the full scope of installation fixing. The differences come down to four points:

  1. Software and engineering. Hilti and Sikla offer design software that works inside BIM models, and Sikla adds a planning service. Atkore offers a hanger configurator and BIM toolbar for its US range. Walraven publishes datasheets and a web catalogue [1][3][4][7].
  2. Load data. Each maker publishes loads in its own format: full tables online, charts, or only in the catalogue. Atkore UK, for example, lists beam loads, deflection limits and column loads per span on each channel page [8]. Compare the same span and the same deflection limit.
  3. Heavy-duty ranges. Beyond 41 mm channel, several brands offer a heavier modular system for large loads, such as Hilti MT and Atkore’s 80×80 heavy-duty framing [4][8].
  4. Supply and support. Which distributors stock it, lead times for cut-to-length and prefabricated frames, and local technical support.

Are strut channels from different brands interchangeable?

Partly. All three manufacturers in our sources use 41 mm as the standard width, with a 22 mm slot opening [9][10]. Channel nuts and fittings therefore often fit another maker’s channel. Serrations, lip profile, gauge and nut design still differ, and some systems use their own profile or nut.

The key point: a published load applies only to the combination the manufacturer has tested. Mix brands and you lose load data for the connection. For a calculated support, specify one system.

What design software do manufacturers offer?

Tool What it does Access Ordering flow for installers
Hilti PROFIS Installation Design, 3D, structural and seismic checks, export to Revit, AutoCAD and IFC Software Not found
fischer FiXperience INSTALL-FIX Step-by-step design, utilisation check, parts list Free, account Not found
Sikla SiCAD Primary and secondary supports in 3D models Plug-ins and service Not found
MÜPRO MP Designer and calculators Channel loads, anchor points, 3D to CAD Free Not found
OBO Construct Cable tray fill, AutoCAD add-in Web and desktop Not found
Atkore Hanger Configurator Trapeze hangers with BIM family and bill of materials Free, registration Prefab quotation, US range
Strut3D Multi-brand design, export to DWG, STEP and STL Subscription Not found

From our research on 19-11-2026 [2–7][11]. “Not found” means we found no public ordering flow; it says nothing about the quality of the tool.

Most of these tools serve the design engineer and are tied to one brand. Estimators and buyers usually need something simpler: a quick bill of materials, a cutting list and a quotation request they can send to a supplier.

How should you compare support systems for a project?

Criterion Question for the manufacturer
Load data Per span, with deflection, for channel, nut and joint?
Corrosion Which finishes, and for which corrosivity class?
Fire Which assemblies are tested for circuit integrity, and to what report?
Standards Channel to BS 6946? Anchors with an ETA for cracked concrete?
BIM and software Objects and tools for our design platform?
Supply Which distributors, what lead time, including cut-to-length and prefab?
Documentation Installation instructions and datasheets in English, with torque values?

Selection criteria, indicative.

On finishes, see pre-galvanised vs hot-dip galvanised vs stainless. Unistrut part numbers are decoded in Unistrut channel sizes.

Where does wire rope suspension fit?

For light services, wire rope suspension such as Gripple’s is a common alternative to threaded rod: a steel wire with a self-locking fastener that is quick to level. The permitted load and the angle at which the wire may hang come from the manufacturer. If you combine containment from one brand with suspension from another, each part brings its own load data, and the joint between them deserves a separate check.

What does brand-independent mean at Strutconfigurator?

The public configurator runs on a standard catalogue that contains only sizes and finishes found at two or more of the three manufacturers we researched, with generic names and no part numbers [12]. Loads are indicative and come from manufacturer data.

A manufacturer or wholesaler gets its own version built on its own range, part numbers, rules and brand. That version then holds one system only, with the load data that belongs to it.

Where do these figures come from?

  1. Walraven, BIS RapidRail documentation. https://files.walraven.com/repository/rnd/documents/BIS-RapidRail-brochure-NL.pdf
  2. MÜPRO, analysis programmes. https://www.muepro.com/services/digital-services/analysis-programmes/
  3. Sikla, software tools. https://www.sikla.de/mainpage-133824/services-133837/software-tools-393124
  4. Hilti, PROFIS Installation. https://www.hilti.in/content/hilti/A1/IN/en/engineering/software/modular-support-design-software/profis-installation.html
  5. fischer, press release on the relaunched FiXperience online suite, 10-11-2025. https://www.fischer.group/en/newsroom/presseinformationen/fischer-fixing-systems/20251110-fischer-relaunches-fixperience-online-suite
  6. OBO Bettermann, OBO Construct. https://www.obo.global/en/service/obo-construct/
  7. Atkore, online tools. https://atkore.com/en-gb/resources/online-tools
  8. Atkore UK, P1000 channel page (BS 6946, load tables) and 80×80 heavy-duty framing. https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P1000
  9. Vergokan (part of Atkore), Unistrut channel pages. https://www.vergokan.com/nl/kabeldraagsystemen/Montagesystemen/Unistrut+profielen___montagerails/P1000T
  10. Eurostrut, 41 mm channel. https://eurostrut.com/montageprofiel-41x41mm-met-gaten-3m-tv/ES1000THDG3M
  11. Strut3D on Capterra. https://www.capterra.com/p/10038872/Strut3D/
  12. Strutconfigurator, standard catalogue v0.1, principles (19-11-2026).

All sources accessed on 19-11-2026.

Frequently asked questions

Is there a difference between strut and Unistrut?

Strut channel is the generic product. Unistrut is a registered brand of Atkore, and on UK sites the name is often used for any 41 mm channel. Other manufacturers make channel with the same outside dimensions, but their fittings and load data belong to their own system.

Can I mix channel and fittings from different brands?

Mechanically they often fit, because many systems are 41 mm wide with a 22 mm slot opening. Published loads only apply to the combination a manufacturer has tested. For a calculated support, stay within one system.

Which manufacturers offer design software for supports?

Hilti offers PROFIS Installation, fischer FiXperience INSTALL-FIX, Sikla SiCAD plug-ins with a planning service, MÜPRO MP Designer and browser calculators, and OBO Bettermann OBO Construct. Atkore has a Hanger Configurator for its US range. Among these manufacturers we found no public ordering flow for installers.

Is Strutconfigurator a dealer for any of these brands?

No. Strutconfigurator is brand-independent and is not a dealer or partner of any manufacturer named here. The public configurator uses a standard catalogue of sizes common to several makers. A manufacturer or wholesaler gets its own version on its own range.

Next step

See your own range in 3D.

In 30 minutes we show how your installers configure, what arrives on your side and what the client version on your range involves.

Manufacturer or wholesaler

Book a demo with Ismail

You see the configurator in your own brand and we discuss your range, systems and markets.

Reply from Ismail within one working day

Installer

Configure for free

A trapeze, frame or tray with cables in a few minutes, with a bill of materials and drawing.

Enquiry goes to a supplier · reply within one working day